Short answer: To choose a PET blow molding machine for water or beverage bottles, start from your bottles, not from the machine: the bottle sizes and shapes, the neck finish and the preform you will use. Then decide the number of mould cavities and whether a semi-automatic or fully automatic machine fits your output and labour. Confirm the compressed air, chiller and cooling water the machine needs, and plan how the bottles will move to the filling line so the blower and the filler run at the same speed. Every figure, from output to air pressure, depends on the model; confirm it in the quotation.
This guide is for investors and factory owners in the Arab countries, the Middle East and Africa who are planning a bottled water, juice or soft drink plant and want to blow their own PET bottles. It covers PET stretch blow molding for bottles only; for injection molding, extrusion and other plastic processes see the Plastic Injection & Blow Molding Buying Guide.
Read also: How to Choose a Water Filling Line · Factory Site Preparation · النسخة العربية · All guides
How PET stretch blow molding works
A PET preform, a small test-tube shaped part with the finished bottle neck, is heated, stretched with a rod and blown with compressed air inside a mould that has the shape of the bottle. The bottle cools against the mould and leaves the machine ready to be rinsed, filled and capped. Because the neck is already formed on the preform, the preform and the cap must match each other and the capping head of your filling machine.
Step 1: Define your bottles
- Sizes and shapes: list every bottle volume and shape you plan to sell now and later. Each shape needs its own mould.
- Neck finish: the neck standard decides the preform, the cap and the capping parts on the filler. Choose it once for the whole line.
- Product: still water, carbonated drinks and hot-filled juices place different demands on bottle design. State your product so the supplier can propose a suitable bottle and process.
- Bottle design: send a drawing or a sample. If you need a new design, ask who makes the drawing and the sample bottles before the moulds are made.
Step 2: Decide where your preforms come from
You can buy preforms from a preform maker or produce them yourself on an injection molding machine. Buying preforms keeps the start simpler; making them adds an injection machine, preform moulds, resin handling and drying, and more staff. Either way, the preform must match the bottle design and the blow mould, so confirm the preform specification with the blow mould maker before ordering either.
Step 3: Moulds and cavities
The number of cavities is the number of bottles the machine blows in one cycle, and it is one of the main factors behind output and price. Ask the supplier how many cavities the proposed machine has for each of your bottle sizes, whether the moulds are included, how long a mould change takes, and whether larger bottles run on fewer cavities. Do not compare two quotations by output alone if they quote different bottles or cavity counts.
Step 4: Semi-automatic or fully automatic
| Point to compare | Semi-automatic blower | Fully automatic blower |
|---|---|---|
| Preform loading and bottle removal | Usually by operators | By the machine, feeding the next conveyor |
| Labour | More operators per shift | Fewer operators, more technical skill |
| Link to the filling line | Bottles are often stored and fed to the filler separately | Can feed the filler directly by conveyor |
| Suits | A small start or a low, flexible output | A continuous line where the blower runs with the filler |
| What to confirm | Output per bottle size, operators needed, safety guards | Output per bottle size, mould change, conveyor interface, controls |
Neither type has a fixed output; it depends on the model, the cavities and the bottle. Ask for the output for each of your bottles in writing.
Step 5: Compressed air, chiller and other utilities
Blow molding uses a lot of compressed air, often at high pressure, plus chilled water for the moulds. These auxiliaries can be a large share of the investment and of the running cost, so confirm them early.
| Utility | Questions to confirm in the quotation |
|---|---|
| High-pressure compressed air | What pressure and flow does the machine need? Is the compressor included, or does the buyer supply it? |
| Air treatment and storage | Are the air dryer, filters and air tank included, and do they match the compressor? |
| Low-pressure air | Does the machine or the line also need low-pressure air for controls or the air conveyor? |
| Chiller and cooling water | Is a chiller included? What cooling capacity and water quality does it need? |
| Electrical power | What is the installed power, and is the machine built for your local voltage and frequency? |
| Space and room | What floor space, height and ventilation do the blower and the compressor room need? |
Step 6: Integrate blowing with the filling line
The blower and the filler should be planned as one line. Agree the target output once and check that the blower, the filler, the labeller and the packer can all run at that output. Ask how the bottles travel from the blower to the filler, for example by air conveyor, and whether a buffer is planned so a short stop on one machine does not stop the other. Some suppliers also offer combined blow-fill-cap machines; ask whether that option fits your bottles and output. The water treatment, filling and site layout are covered in the water filling line guide and the site preparation guide.
What to send for a quotation
- Your product: still water, carbonated drink, juice or other.
- Bottle sizes and shapes, with drawings or samples, and the neck finish.
- Whether you will buy preforms or make them, and the preform specification if you have one.
- Target output for the whole line and working hours per day.
- Whether you want a semi-automatic or fully automatic blower, or a recommendation.
- Country, local voltage and frequency, and building dimensions.
- Whether the quotation should include the compressor, air treatment, chiller, moulds and conveyors.
Common mistakes
- Choosing the blower before fixing the bottle designs and the neck finish.
- Comparing outputs from quotations that use different bottles or cavity counts.
- Leaving the high-pressure compressor and the chiller out of the budget.
- Buying a blower that does not match the output of the filler.
- Ordering preforms before the blow mould maker has confirmed they suit the bottle.
How Rendat helps
Rendat is an industrial machinery group based in Yiwu, China. Servolines is its brand for water and beverage lines, covering water treatment, bottle blowing, filling and capping, labelling and packing. Renplas is its plastic machinery brand, supplying injection molding machines, including for preforms and caps, and extrusion, film and recycling lines. Other brands are Ferrni for bakery and pastry, Renfoo for animal feed, Niopac for packaging and Eirmac for metal working, with spare parts through RendatSP. Which machines, moulds and auxiliaries are included in your project is set out item by item in the quotation.
FAQ
What is a PET stretch blow molding machine?
It is a machine that heats PET preforms, stretches them with a rod and blows them with compressed air inside a mould to form bottles.
Should I make my own preforms or buy them?
Buying preforms keeps the start simpler. Making them adds an injection molding machine, preform moulds and resin drying. In both cases the preform must match the bottle and the blow mould.
How many cavities do I need?
It depends on your bottle sizes and target output, and on the model. Ask the supplier for the cavity count and output for each bottle in writing.
Is a semi-automatic blower enough?
It can suit a small start with a low, flexible output. A continuous line that feeds the filler directly usually needs a fully automatic blower. Confirm the output for your bottles in the quotation.
Is the air compressor included with the blow molding machine?
Not always. Ask whether the high-pressure compressor, air dryer, air tank and chiller are included, and what pressure, flow and cooling the machine needs.
Request a quotation
Send us your bottle sizes, neck finish, product, target output and country, and we will propose a blower matched to your filling line. Request a quote or WhatsApp +86 181 5871 1787.
Related links
- How to Choose a Water Filling Line
- Factory Site Preparation Before Installing a Production Line
- Production Line After-Sales Service: Installation, Training and Spare Parts
- Plastic Injection & Blow Molding Buying Guide
- Plastic Manufacturing Plant Cost: What Determines the Price
- All guides
- بالعربية: دليل شراء ماكينة نفخ عبوات PET